| Release Level |
Date |
Purpose |
| R10V |
09/08/2010 |
Update |
| R10U |
06/21/2010 |
Update |
| R10T |
06/04/2010 |
Update |
| R10R |
03/10/2010 |
Update |
| R10Q |
02/08/2010 |
Update |
| R10P |
01/14/2010 |
Update |
| R10N |
01/07/2010 |
Update |
| R10M |
12/18/2009 |
Update |
| R10L |
07/01/2009 |
Update |
| R10K |
06/24/2009 |
Update |
| R10J |
05/06/2009 |
Update |
| R10H |
03/06/2009 |
Update |
| R10G |
03/04/2009 |
Update |
| R10F |
02/26/2009 |
Update |
| R10E |
02/24/2009 |
Product Launch |
|
|
R10V
EVM [All Models]
Updates
- Added support for ozone (O3)
- Added support for mechanical impactors.
Back to top of page |
|
R10U
EVM [All Models]
Updates
- PID (PPM sensor) displays hundredths from 0 to 500 mg/m^3 (was displaying tenths)
Back to top of page |
|
R10T
EVM [All Models]
Updates
- Measurements - PID (PPM sensor) measurement is displayed in hundredths from 0 to 20 PPM.
- Calibration - Pump duty cycle is displayed while performing a user calibration. (Prior to this release, it could display dashes).
Back to top of page |
| R10R
EVM [All Models]
Updates
- Added molecular weight to log files allowing QuestSuite to convert between PPB (PPM) and ug/m^3 (mg/m^3) for PID measurements (used for LEED initiative).
Back to top of page | |
| R10Q
EVM [All Models]
Updates
- Measurements and calculations- Added ug/m^3 as an alternate user unit for PID (PPB) sensor.
- Measurements and calcuations- Added mg/m^3 as an alternate user unit for PID (PPM) sensor.
Back to top of page |
| R10P
EVM [All Models]
Updates
- PID ppb (sensor) Internal Calibration Update: Changes the baseline (zero ppb) as requested by the manufacturer.
Back to top of page |
R10N
EVM [All Models]
Updates
- Language update: Revised Portuguese translations for PID, RH (Relative Humidity) and Dew Point.
- Particulate Measurements: Corrected the occasional false positive "laser not working properly" error message on extended logs (4+ hours).
- CO2 and PID measurements: Corrected the infrequent CO2 and PID measurement errors (CO2 measurement goes to zero, PID measurement goes to > 1 PPM).
- Display: Various minor display issues resolved.
Back to top of page |
R10M
EVM [All Models]
Product Enhancements
- Auto-Run with Date, Date of Week, and Timed-Run modes have been programmed, tested and released.
- File System Sessions menu: Added sorting to file system sessions. Sessions are now displayed in date descending order. (This is accessed from the following menus: From Start screen: File System/Session Directory. Press Enter to toggle through 3 different views.)
Updates
- PID measurements: PID lamp is turned off when not needed to extend life.
- PID PPB calibration: PID (PPB only) sensor only supports a span calibration (user zero calibrations are not needed).
Back to top of page |
R10L
EMV [All Models]
Displayed System Errors
- Eliminated multiple user notifications when the file system is full during a logging session.
- Eliminated multiple user notifications when the system is in secure run mode and the impactor position is changed during logging.
Back to top of page |
| R10K
EVM [All Models]
Updates
Measurements and calculations
- Allow users the option to save additional log interval values: Lmax, Lmin, Lavg and Lmax_stel.
- Added dew point as a (calculated) parameter.
- Added ug/m3 as an alternate user unit for particulate matter (PM).
PID Measurements
- Added a PhotoIonization (PID) correction factor for the PID sensor when measuring a specific Volatile Organic Compound (VOC).
- Added support for a Parts Per Billion (PPB) Photoioniztion (PID) sensor.
Security/Lock feature Added
- Added secure run and setup modes.
Back to top of page |
| R10J
EVM [All Models]
Updates
Particulate Matter Pump
- Disable the Particulate Matter (PM) pump when it is unable to regulate at 1.67 L/min.
Calibration
- The calibration screens now displays the details of factory calibrations.
- The user settable span calibration value is set to the previous user span calibration value as a convenience.
Unit Info screen updated
- The hardware version is now displayed in the UNIT INFO screen.
Back to top of page |
| R10H
EVM [All Models]
Updates
CO2 sensor
- Corrected a timing issue that caused the CO2 sensor value to go under range periodically.
Back to top of page
|
| R10G
EVM [All Models]
Updates
- Corrected a hardware issue sometimes leading the unit to display a system error message and invalidating the measurements from various sensors.
- Corrected minor user interface refresh errors.
Back to top of page
|
| R10F
EVM [All Models]
Updates
- Fully display the toxic serial number in the UNIT INFO screen (the last digit was truncated).
- Large log files can now be downloaded without the system resetting.
- The Particulate Matter (PM) user correction factor is now immediately applied (a power cycle used to be required).
Back to top of page |
|
R10E
EVM [All Models]
Product Launch
- First official firmware release.
Back to top of page |
|
|